BlastIQ™ Mobile Release 2023

BlastIQ Mobile

A new version will be offered to users in October  2023. A notification will appear in BlastIQ Mobile on start-up once the update is available. We hope this will enable customers to perform the update without assistance from the specialist. 
For further information on an update to the software, please contact the Support Team at blastiqsupport@orica.com or via web support.blastiq.com.

October

1.20.234

Update 24th October 2023

  Fixed

  1. Fixed the "Enforce Dipping Before Loading" issue.  
    • Users will be prompted to specify the hole depth before loading when this feature is enabled via the Admin portal.


September

1.20.114

Update 28th September 2023

  New

  1. PIN Access. Read more here.PIN.png

  Improved

  1. Filter Drill Plan Improvements. Read more here.
    • Users can now filter designed air and stemming decks.
    • Status icons have been added for all hole status checkboxes.FilterDrillPlan.png
  2. Delivery Summary. Read more here.
    • Inert products have been included in the delivery summary.
  3. When the temperature mode is activated on the measurements map, a floating window will display the temperature legend.TemperatureLegend.png
  4. The legend on the measurements map has been removed. Legend.png

  Fixed

  1. Stability Improvements:
    1. We've located and resolved a long standing, intermittent update bug. This bug could cause measurements not to appear in the user interface and sometimes lead to app crashes.
    2. We've added more defensive code to handle the device entering and leaving sleep / suspend modes, reducing the likelihood of app crashes.

August

1.19.139

Update 31st August 2023

  New

  1. Addition of pause and resume buttons to the drilling timer. Read more here, in the Drilling a Hole section.
    1. Both length and drilling time values are used to post the Average Penetration Rate. These values are surfaced in the BlastIQ Insights Overview and Drilling Quantities dashboards. 

Drilling Time.png

  Improved

  1. Build screen updated to support upcoming licencing rollout. Read more here.

    NewBuildScreen.png

  2. Delivery summary user interface enhancements to accommodate upcoming functionality.

    DeliverySummary.png

  3. Diameter filter dialogue -  changed to portrait orientation to minimise screen footprint.

    DiameterLegend.png

  4. Map action buttons remain visible at all times.
    • Drilling hole editor in open state.

      Open.png

    • Drilling hole editor in closed state.

      close.png

  1. Loading rules toggle has been removed from the drill plan list to ensure consistency of the 'backfill required' and 'redrill required' hole tags across the system. Users should use SHOTPlus™ to control whether tolerances or loading rules are sent and applied in the field.

RemovedLoadingRules.png


July

1.18.39

Update 13th July 2023

  Fixed

  1. Fixed an issue for wet sides loading rules.
  2. Fixed an issue for wet/dry trigger loading rules (SP6 graphical charging rules).
  3. Fixed intermittent sync performance issue.

 

Wet Side Loading rules will be supported in an upcoming release of SHOTPlus.

  Improved

  1.  On the device set-up page, only sites with a valid Blast Control license will be displayed.

1.18.13

Update 5th July 2023

  New

  1. Support for wet-side loading rules has been added.
  2. Support for tolerance-based wetness in graphical charging rules has been implemented (previously considered any water as wet).

 

Please note that future releases of SHOTPlus will be required to take advantage of these updates.


June

1.17.265

Update 26th June 2023

  Improved

  1. Temperature validation range updated to -50 °C to 999 °C, inclusive.
  2. Drill Actuals Capture:
    1. Increased hole size scaling for better visualisation.
    2. Increased hole hit area for better experience in the selection of holes.
    3. When a user enters a set of drill actuals and clicks on another hole on the map, a modal will appear, prompting the user to confirm if they want to proceed without saving the changes.
  3. Closing application screen is shown when the Exit button is used to close the application.
  4. Monitoring improvements related to expected networking issues.

May

1.17.73

Update 16th May 2023

  New

  1. New loading hole type tolerance to trigger deck warnings. Read more here.

  Improved

  1. Removal of edit button from the hole details panel.
    • Aims to enhance usability by reducing the need for unnecessary clicks and taps. Read more here.
  2. 'Holes deviated from design' toggle has been added to the delivery summary.
    • Allowing users to view the total actual weight and initiation accessory counts including holes that deviate from the design. DeviatedHole.png

  Fixed

  1. Fixed the Nan displays on the Maintenance page - Event Database Size section.
  2. On the drilling mode, adding a hole and marking it as a 'redrill of' another previously added (redrill) hole was causing the app to crash.

March

1.16.159

Update 1st March 2023

  New

  1. Drilling Timer, Diameter and Bearing Indicators, Drill Summary Panel. Read more here.

    DrillingSummary1.png

  2. Multi-line Plan Notesmultiline_plan_notes.png

  Bug Fixes

  1. Clearing an existing drill actual length now displays the correct value instead of 'null'.
  2. Actuals are visible and user can now save when clearing redrill of from the drop down menu.
Was this article helpful?
0 out of 0 found this helpful
Have more questions? Submit a request