Designing and Using a Traffic Management Plan (TMP) Map with Next Gen SHOTPlus™ and BlastIQ™

Purpose

This document explains how to design a traffic management plan (TMP) map for a blast, share it with the BlastIQ™ site, and use it on the bench. It covers the full process from the design in Next Gen SHOTPlus™ to the review and updates in BlastIQ™ Insights/Mobile.

The TMP helps everyone on the bench understand:

  • Where vehicles and people enter and exit the blast area.
  • Which areas are no-go areas.
  • How traffic should move around the pattern.
  • Any other hazards or controls specific to the blast.

Before you start

  • The blast design is available in Next Gen SHOTPlus™ BlastIQ™ Insights.
  • You have access to the correct site in BlastIQ™.
  • The BlastIQ™ site has been configured with Required Blast Documentation (Job Pack) to allow file sync to BlastIQ™ Mobile devices.
  • The BlastIQ™ Mobile app is installed on the device used on the bench, and you are signed in.
  • The mobile device can download the file before going to the bench, in case there is no network signal.

Workflow overview

StepActionTool
1Design the blast and add the TMP markupNext Gen SHOTPlus™
2Export the design to PDFNext Gen SHOTPlus™ (print to PDF)
3Upload the PDF to the BlastIQ™ siteBlastIQ™ Insights (job pack)
4Review the TMP on the benchBlastIQ™ Mobile
5Mark up changes if bench conditions changeBlastIQ™ Mobile

Step 1: Design the blast and TMP markup in Next Gen SHOTPlus™

Complete the blast design first, then add the traffic management markup on top of it in a new layer.

  1. Open the blast design in Next Gen SHOTPlus.
  2. Confirm the pattern, holes and design details are final, or close to final.
  3. Make sure the site map or background layer is visible, so roads, ramps and the bench edge show on the plan (if available).
  4. Add the TMP markup described below.
  5. Check that the markup is clear and easy to read when zoomed out.
  6. Save the design.

What to mark up

ItemWhat to show
Entry and exit pointsWhere vehicles and people enter and leave the blast area, including the access road or ramp.
No-go areasAreas that must not be entered, such as soft / unstable ground, or the area below a highwall or close to the low wall.
Traffic flowDirection of travel for vehicles, with arrows. Show one-way routes and turning areas.
Loading sequenceThe sequence the blast will be loaded, with arrows.
Parking and staging areasWhere the blasting crew, explosives trucks and support vehicles should stop/park up.
Other hazardsWater, wet holes, overhead power lines, edges, soft ground or anything else specific to this bench.

Use the same colours and symbols on every blast so the plans are familiar to the crew. Follow the site's standard if one exists.

Step 2: Export the design to PDF

  1. In Next Gen SHOTPlus™, set the view so the whole blast and all TMP markup are visible.
  2. Choose the print option (Reporting > Plan) and select a PDF printer (print to PDF) as the printer.
  3. Choose a paper size and orientation that suit the plan. Use a larger paper size if the markup is hard to read.
  4. Check the print preview. Make sure the markup and hole labels are readable.
  5. Save the PDF with a clear name, for example: Site_Bench_BlastID_TMP.pdf.
  6. Open the saved PDF and check it before you upload it.

Step 3: Upload the PDF to the BlastIQ™ site

  1. Sign in to BlastIQ™ Insights and open the correct site.
  2. Go to File Storage > Blast Files and select the blast.
  3. Upload the TMP PDF to the correct required document.
  4. Check that the file appears with the right name and opens correctly.
  5. Check that the right people have access to the file, including the crew who will use BlastIQ™ Mobile.

Step 4: Review the TMP on the bench in BlastIQ™ Mobile

  1. Open BlastIQ™ Mobile and select the blast and select Measure & Load.
  2. Select the Blast file button

  1. Select the Sync button and open the file using the File view button.

Step 5: Mark up changes if bench conditions change

Conditions can change after the TMP map is made. Examples include a blocked access road, a new wet area, or a change in where vehicles need to park.

  1. Open the TMP file in BlastIQ™ Mobile.
  2. Use the markup tools to mark the change on the plan. For example, draw a new no-go area or change the traffic flow arrows.
  3. Add a short note that says what changed and why.
  4. Save the marked-up file and re-sync with BlastIQ™.

Tips

  • Keep the plan simple. Too much detail makes it hard to read on a phone or tablet.
  • Use clear colours and arrows.
  • Download the file before going to the bench, in case there is no signal.
  • Include the blast ID and date on the PDF so it is easy to match to the right blast.
  • Remove or replace old versions of the TMP so the crew only sees the current one.
Was this article helpful?
0 out of 0 found this helpful
Have more questions? Submit a request